http://ijaems.com/ Open Access international Journal to publish research paper en-us November 2016 Static synchronous compensator (STATCOM) is a regulating device used in AC transmission systems as a source or a sink of reactive power. The most widely utilization of the STATCOM is in enhancing the voltage stability of the transmission line. A voltage regulator is a FACTs device used to adjust the voltage disturbance by injecting a controllable voltage into the system. This paper implement Nruro-Fuzzy controller to control the STATCOM to improve the voltage profile of the power network. The STATCOM controller has simulated for some types of abnormal conditions. The simulation results show improves the system voltage profile. The performance of compensator with its new controller was very close to the nominal value, which was 98% of the busbar voltage. http://ijaems.com/detail/voltage-profile-improvement-using-static-synchronous-compensator-statcom-2/ Mohammed Y. Suliman http://ijaems.com/upload_images/issue_files/1 IJAEMS-OCT-2016-33-Voltage profile Improvement Using Static Synchronous Compensator STATCOM.pdf The reaction between the various hosts with Pisolithus tinctorius shows the broad host range of this fungal species showing different degrees of host compatibility. There is wide variation in both rate and extent of ECM formation by different isolates of Pisolithus tinctorius of different geographical regions within a species. Thus Pisolithus tinctorius displays much intraspecific heterogeneity of host specificity and interspecific compatibility. There are variable degrees of plant-fungal isolate compatibility, implying specificity, and this is an important factor influencing successful ectomycorrhiza formation and development. The molecular data also suggested that the Pisolithus tinctorius isolates analyzed from different geographical regions belong to distinct groups. Further studies are therefore warranted to elucidate the molecular, biochemical and physiological differences between the Pisolithus tinctorius isolates at the fungus-root interface of different plant species. http://ijaems.com/detail/host-specificity-mycorrhizal-compatibility-and-genetic-variability-of-pisolithus-tinctorius/ Hemavathi Bobbu http://ijaems.com/upload_images/issue_files/2 IJAEMS-NOV-2016-2-Host specificity, mycorrhizal compatibility and genetic variability of Pisolithus tinctorius.pdf This brief study compares the proposed RGSA algorithm with other recent methods by several experiments to indicate that proposed 3DGLCM and SGLDM with SVM classifier is more efficient and accurate. The accuracy results of this study imply how well their experimental results were found to give more accurate results of classifying tumors. The center of interest for this study was made on supervised classification approaches on 2D MRI images of brain tumors. This paper gives the comparative study of various approaches that was used to identify the tumor cells with classifiers. http://ijaems.com/detail/comparative-study-on-medical-image-classification-techniques/ Dr Rajesh Sharma R, P S Renisha, Dr Akey Sungheetha http://ijaems.com/upload_images/issue_files/3 IJAEMS-NOV-2016-3-Comparative Study on Medical Image Classification Techniques .pdf The selection of vegetable tanning agents is important in tanning industry because they can generate environmental and economic impact. Environmental effect such as contaminating fresh water aquatic ecotoxicity and human toxicity is the problems of tanning industry. Based on economic aspect, the price and saving cost is the effect of the use of vegetable tanning agent. This research was conducted to analyze the impact of vegetable tanning agents selection based on environmental and economic aspect. To evaluate the impact of environment, the simulation software was used. The fuzzy multi-attribute decision making was also used to selection process to find the best vegetable tanning agents based on environmental and economic aspects. http://ijaems.com/detail/analyze-the-environment-and-economic-impact-of-vegetable-tanning-agents-selection/ Salman Alfarisi, Udisubakti Ciptomulyono http://ijaems.com/upload_images/issue_files/4 IJAEMS-OCT-2016-29-Analyze the Environment and Economic Impact of Vegetable Tanning Agents Selection.pdf We have done mapped earthquake-prone zonation of North Bengkulu, Indonesia, based on peak ground acceleration by kanai’s and Katayama’s formula. Twenty nine microtremor data have recorded by Digital portable Seismometer that installed in North Bengkulu regency. The result of HVSR analysis, we got resonance frequency and A0 which explained the condition of surface rocks. Peak ground acceleration on rock surface which applied local geology condition (dominant period of natural soil vibration). Based on A0 value, the risk of earthquakes in north Bengkulu was on moderate to high level because this area has relatively soft rock structure. Kanai's formula has correlation near 70.6% with Katayama's formula to showed PGA value on rock surface. Peak Ground acceleration of Kanai formula in North Bengkulu about 152,441 - 674,391 gal and based on Katayama formula between 35.2 gal until 51.3 gal. Based on PGA value, we estimated that North Bengkulu has on IV and IX of MMI scales. It meant that in North Bengkulu potential have heavy damage when an earthquake occurred. Distribution of PGA values based on the observation has correspond to effects earthquake of North Bengkulu at September 2007. http://ijaems.com/detail/earthquake-prone-zonation-of-north-bengkulu-based-on-peak-ground-acceleration-of-katayama-s-and-kanai-s-formula/ Budi Harlianto, Nanang Sugianto, Irkhos http://ijaems.com/upload_images/issue_files/5 IJAEMS-OCT-2016-30-Earthquake-prone Zonation of North Bengkulu Based on Peak Ground Acceleration of Katayama’s and Kanai’s Formula.pdf The paper examines the impact of brand awareness on buying behavior through various literatures. Creating brand awareness and providing unique information about the brand and also creates brand image in the minds of consumers. Advertisement a plays a major role and an effective tool used to create brand awareness. Brand awareness is one of the marketing factors in determine the buying behavior. Consumers do build optimistic opinion about a brand on the basis of information provided by the companies. http://ijaems.com/detail/a-review-on-advertisement-the-vein-of-marketing-with-special-reference-to-textile-retail-showrooms-chennai/ Mrs. P. Suganya Devi., Dr. Vijayadurai http://ijaems.com/upload_images/issue_files/6 IJAEMS-NOV-2016-1-A Review on Advertisement - The Vein of Marketing with Special Reference to Textile Retail Showrooms, Chennai.pdf This paper intends to find Expected monetary value (EMV), Expected opportunity loss (EOL) and conditional profit of the main product (Mukta) of a small scale industry–“ORGAMAN” situated at Jorhat District of Assam. To meet the above specific objectives, the method of Bayesian Analysis has been adopted. The data used in this endeavor is secondary in nature, collected by direct personal investigation. As per prior information, the target of the industry is to produce a minimum of 50 MT (low production) of product and a maximum of 350 MT (high production) of the same per month. The prior analysis reveals that the expected monetary value and expected opportunity loss are optimum against high production. Based on both the prior analysis and posterior analysis, it is observed that the profit for the product of the industry is maximum against high production of 350 MT per month. Although, the profit based on posterior analysis is slightly high, it seems that the additional amount of money has to be spend to collect additional information for posterior analysis. http://ijaems.com/detail/decision-making-in-optimizing-a-product-of-a-small-scale-industry-a-bayesian-analysis-approach/ S. Bharali, A.N. Patowary, J.Hazarika http://ijaems.com/upload_images/issue_files/7 IJAEMS-NOV-2016-5-Decision Making in Optimizing a Product of a Small Scale Industry_ A Bayesian Analysis Approach.pdf System describes a real-time online trial product driver-fatigue monitor or driver tiredness is captured. It means to capture the current state or mode of tiredness of driver whether the driver is in sleeping state or in wakening state. It uses remotely located charge-coupled-device cameras able to with active infrared illumination to acquire video images of the driver. Various cues that typically stated the level of attentiveness of a person that how an person is attentive are removed or take out in real time and systematic combined to infer the tiredness level of the driver. The some cues employed stated eyelid movement, steady movement, head movement, and facial expression. This is developed to model human fatigue and to know about fatigue based on the visual cues obtained. The simultaneous use of multiple optical cues and their methodical combination yields a much more robust and accurate fatigue categorization than using a single visual cue. This system was valid as real-life fatigue conditions with human subjects of different cultural backgrounds, genders, and ages as with or without glasses, and under different illumination conditions. It was found to be sensibly robust, reliable, and accurate in fatigue categorization. http://ijaems.com/detail/a-novel-approach-for-eye-tracking-using-driver-fatigue-monitoring/ Ms. Neha Bhalerao, Ms. Snehal S. Sawant, Ms. Dipali C. Pathade, Ms. Vandana S. Singh, Prof. K. S. Kumavat http://ijaems.com/upload_images/issue_files/8 IJAEMS-NOV-2016-11-A Novel Approach for Eye Tracking using Driver Fatigue Monitoring _2.pdf This article presents a design of wavelength division multiplexing/ Time division Multiplexing (WDM-TDM) in passive optical network with a data rate of 10 Gbps. The implementation has been carried out for varying link distance from 40km to 100km for 4 different wavelengths with a maximum of 32 supporting users with two different receiver photodiodes. The parameters such as BER and the Q-factor for PON network is being analyzed with the link distance. The BER is decreased as the distance of the network is increased when using the APD receivers than PIN receiver. Optimal value of BER is obtained for a distance of 97 Km in APD and 96 Km in pin receiver. http://ijaems.com/detail/analysis-on-design-and-implementation-of-4-10-gb-s-wdm-tdm-pon-with-disparate-receivers/ Sreekar Chintalapati, Praveen Samudrala, P.Karthik Reddy, Prof. Rajalakshmi S http://ijaems.com/upload_images/issue_files/9 IJAEMS-NOV-2016-6-Analysis on Design and Implementation of 4×10 Gb_s WDM-TDM PON with Disparate Receivers.pdf The scope of this paper is to analyze the performance of HG_EDFA (High Gain Erbium Doped Fiber Amplifier) and LN_EYCDFA (Less ASE Noise erbium-ytterbium co-doped fiber amplifier) using single pumping with the wavelength of 980nm by the various parameters like Gain, forward output signal power and forward and backward ASE (Amplified spontaneous Emission) noise power. This Paper describes the simulation models of HG_EDFA is connected with an input of (DMLaser1) direct modulated laser source and the performance was analyzed with the parameters were measured and the values are tabulated and plotted and compared with LN_EYCDFA. The simulation model consists of input source 1mw with wavelength (1550nm), pumping CW Laser source with wavelength 980nm and Filter. The resulting models were accurately represents Gain and optimized output signal power. Simulation results shows that by choosing careful fiber length 20m and pump power 1mw in single pumping gives ASE noise 0.0025mw in HG_EDFA and 12X10-14mw in LN_EYCDFA. http://ijaems.com/detail/performance-analysis-of-hg-edfa-and-ln-eycdfa/ S. Semmalar, S. Malarkkan http://ijaems.com/upload_images/issue_files/10 IJAEMS-NOV-2016-8-Performance analysis of HG_EDFA and LN_EYCDFA .pdf This study aims to select the representative Kansei adjectives or words in Kansei engineering methodology. This study used the passenger car design as its experimental case study. A two-stage cluster analysis was carried out for selecting the representative Kansei adjectives. The selection process of the representative Kansei adjectives was determined based on the smallest distance of individual Kansei adjective to the centroid of each cluster. Thus, the results indicated that ‘modern’, ‘elegant, ‘sporty’, and ‘youthful’ were thereupon selected as appropriate adjectives to represent the initial set of Kansei adjectives. As a conclusion, the cluster analysis method was able to systematically select the representative Kansei adjective and easily interpretable for Kansei engineering. http://ijaems.com/detail/selection-of-representative-kansei-adjectives-using-cluster-analysis-a-case-study-on-car-design/ Sugoro Bhakti Sutono http://ijaems.com/upload_images/issue_files/11 IJAEMS-NOV-2016-7-Selection of Representative Kansei Adjectives using Cluster Analysis_ A Case Study on Car Design.pdf The main objective of the current study is to investigate the effects of organizational culture on organizational health. Modern organizations are in a very intense competitive conditions and in order to survive, they need parameters which guarantee their survival. Therefore, the current study will investigate the significance of culture in this regard. Municipalities as one of the organizations providing urban services are in a position where it is possible to lose their impact due to the activities of other organizations. Accordingly, the statistical population selected for this study includes all the employees in Tehran Municipality. In order to gather the required data, after determining the sample size as 384 participants using Krejcie and Morgan table, standard questionnaire of Denison for culture (2000) and organizational health (2008) were used. The current study is a quantitative one carried out as a descriptive survey. The validity and reliability of the study are confirmed using appropriate methods. Finally, in order to test the hypotheses of the study, various descriptive and inferential statistical tests were used. It was found out that the organizational survival of Municipality was affected by various cultural parameters, among which compatibility had the highest impact. http://ijaems.com/detail/effect-of-organizational-culture-on-organizational-health/ Ramin Noori, Mehdi Sabokro http://ijaems.com/upload_images/issue_files/12 IJAEMS-NOV-2016-9-Effect of Organizational Culture on Organizational Health.pdf Computer networks have experienced an explosive growth over the past few years, which has lead to some severe congestion problems. Reliable protocols like TCP works well in wired networks where loss occurs mostly because of congestion. However, in wireless networks, loss occurs because of bit rates and handoffs too. TCP responds all losses by congestion control and avoidance algorithms, which results in degradation of TCP’s End-To-End performance in wireless networks. This paper discusses different issues and problems regarding use of TCP in wireless networks and provides comprehensive survey of various schemes to improve performance of TCP in Wireless Networks. http://ijaems.com/detail/tcp-for-wireless-environments/ Mr. Ranjeet V. Bidwe, Mr. Mahesh A. Kandekar http://ijaems.com/upload_images/issue_files/13 IJAEMS-NOV-2016-21-TCP for Wireless Environments.pdf This paper presents an application of the novel evolutionary algorithm for assessing financially an economic power system operation throughout a combined economic and emission dispatch problem required by various technical limitations. In detail, this problem considers two dispatches for fuel and environmental aspects as a constrained objective function associated with weighting factor scenarios. Running out simulations show that minimum costs are depended on weighting factors, which implemented on the combination of the problem. Reducing the total fuel cost focused on the dispatching priority and the pollutant target based on the emission production have difference implications as its contribution to the economic operation, the increasing load demand leads to generated powers, costs and emission discharges associated with its parameters and power schedules. http://ijaems.com/detail/financial-assessment-considered-weighting-factor-scenarios-for-the-optimal-combination-of-power-plants-on-the-power-system-operation/ A.N. Afandi, Yunis Sulistyorini, Hajime Miyauchi, Goro Fujita http://ijaems.com/upload_images/issue_files/14 IJAEMS-NOV-2016-22-Financial Assessment Considered Weighting Factor Scenarios for the Optimal Combination of Power Plants on the Power System Operation.pdf The administration of IAA on the total proteins, protease activity, free amino acids, alanine amino transferase (ALAT) activity and aspartate amino transferase (AAT) activity were studied. The increase of total protein content in silk gland may be either due to increased efflux or decreased proteolysis activity which might lead to accumulation of protein content. The decrease in protease activity level in silk gland may be due to lower rate of histolysis. The decrease in the free amino acid content indicates the faster mobilization of free amino acids into oxidative metabolism in the presence of IAA. The ALAT and AAT activity levels were elevated after treatment indicating the active involvement in the protein synthesis. http://ijaems.com/detail/pattern-of-changes-in-the-amino-acid-levels-in-silk-gland-of-silkworm-bombyx-mori-l-treated-with-indole-3-acetic-acid-iaa/ D. Bharathi http://ijaems.com/upload_images/issue_files/15 IJAMES-NOV-2016-15-Pattern of changes in the amino acid levels in silk gland of silkworm, Bombyx mori L.treated with Indole-3-acetic acid ( IAA).pdf Coated and uncoated tool inserts offers certain degrees of control on the desired rate of tool wear and surface roughness to an extent. This work pursues the quest for realizing the optimal values for the significant process parameters that bears an influence on the response parameters. Experiments were conducted on the samples of EN 24 alloy steel material with the help of PVD coated TiAlN insert and uncoated carbide insert. The experimental runs carried out with proper variation in the levels. Levels are selected with the help of manufacturing catalogue and by pilot experimentation and results are recorded for further analysis. For this study, 9 runs designed using L9 orthogonal array of Taguchi Design of Experiment. Surface roughness was measured using a Mitutoyo surface tester at test lab and material removal rate is calculated by mathematical equation. The data was compiled into Minitab 17 software for analysis. The relationship between the machining parameters and the response variables were analyzed using the Taguchi Method. Optimization of process parameters is carried out by Grey Relational Analysis method (GRA). GRA method is a powerful and most versatile tool which can manipulate the input data as per requirement and comes with results that can be used to have best multi-objective in respective concerns. http://ijaems.com/detail/optimization-of-process-parameters-for-cnc-turning-using-taguchi-methods-for-en24-alloy-steel-with-coated-uncoated-tool-inserts/ Suraj R. Jadhav, Aamir M. Shaikh http://ijaems.com/upload_images/issue_files/16 IJAEMS-NOV-2016-20-Optimization of Process Parameters for CNC Turning using Taguchi Methods for EN24 Alloy Steel with Coated_Uncoated Tool Inserts.pdf The rising interest in NoSQL technology over the last few years resulted in an increasing number of evaluations and comparisons among competing NoSQL technologies From survey we create a concise and up-to-date comparison of NoSQL engines, identifying their most beneficial use from the software engineer point of view. http://ijaems.com/detail/the-rising-nosql-technology/ Sumati Baral http://ijaems.com/upload_images/issue_files/17 IJAEMS-NOV-2016-14-The Rising NoSql Technology.pdf Semantic annotation, which is considered one of the semantic web applicative aspects, has been adopted by researchers from different communities as a paramount solution that improves searching and retrieval of information by promoting the richness of the content. However, researchers are facing challenges concerning both the quality and the relevance of the semantic annotations attached to the annotated document against its content as well as its semantics, without ignoring those regarding automation process which is supposed to ensure an optimal system for information indexing and retrieval. In this article, we will introduce the semantic annotation concept by presenting a state of the art including definitions, features and a classification of annotation systems. Systems and proposed approaches in the field will be cited, as well as a study of some existing annotation tools. This study will also pinpoint various problems and limitations related to the annotation in order to offer solutions for our future work. http://ijaems.com/detail/semantic-annotation-of-documents-a-compar-ative-study/ Hasna Abioui, Ali Idarrou, Ali Bouzit, Driss Mammass http://ijaems.com/upload_images/issue_files/18 IJAEMS-NOV-2016-19-Semantic Annotation of Documents_ A Compar-ative Study.pdf This research is capable to do cryptography with multi keywords search. This research is target to provide search files from cloud network using multi keywords. This paper is target to provide a security at the maximum level by includes encryption and decryption. The administrator has control of authorization and allowing files to move more secured. Encryption and decryption of files and file names which is used symmetric and asymmetric algorithm respectively. The unique key is generated for every users to protect other user cannot access the files. While implementing this project the user can understand very simple environment. The user can reduce incapable systems in server side process to hold most of the processes. The client side system has used less work for the corresponding task to perform the necessary role like arranging and ranking the files from requested order. This project can apply in various applications for this user friendly. http://ijaems.com/detail/enhanced-secure-multi-keyword-top-k-retrieval-in-cloud/ Ahmad Tasnim Siddiqui, Syed Ajaz, Isbudeen Noor Mohamed http://ijaems.com/upload_images/issue_files/19 IJAEMS-NOV-2016-27-Enhanced Secure Multi Keyword Top-K Retrieval in Cloud.pdf